Hydro jetting nozzle spraying water inside a drain opening

Hydro jetting

Hydro jetting and Sewer Jetting in South Florida

High-pressure water cleaning for drain and sewer lines in Miami-Dade, Broward, and Palm Beach Counties. Used to scour grease, sludge, scale, and debris when the pipe can take it.

What hydro jetting does

Hydro jetting, also called sewer jetting or water jetting, cleans a drain or sewer line with high-pressure water. A hose is fed into the pipe through a cleanout or other access point, and a nozzle on the end sprays water backward against the pipe wall. That backward spray pulls the hose forward and scours the whole circumference of the pipe as the hose is pulled back. Grease, sludge, soap film, sand, scale, and roots are broken loose and flushed back out of the line.

That is the main difference from a cable machine or snake. A cable bores a hole through the middle of a clog and restores flow, but it often leaves the coating on the walls in place. Jetting removes it, so the line is far less likely to close up again in a few weeks. Read more in What is hydro jetting? and hydro jetting vs. snaking.

Our hydro jetting process

Talk it through

You tell us what the line is doing: which fixtures, how often, and since when. Call (954) 914-5151.

Camera first

When the line can be seen, a camera inspection shows what is inside and whether the pipe can take pressure.

Jet the line

We choose the nozzle and pressure for the pipe: penetrating, flushing, root-cutting, or descaling.

Verify

A second camera pass, when possible, shows you that the pipe wall is actually clean.

Jetters for lines from 1 inch to 36 inches and larger

We have jetters for lines from 1 inch up to 36 inches and larger pipes. We run hydro jetters in several sizes, from trailer-mounted units to combination vac/jetter trucks. That covers everything from a kitchen branch line to a large storm or commercial main. HD sewer cameras are used to check conditions before and after the work.

When hydro jetting is the right call

  • A main line that keeps clogging in the same place
  • Restaurant and commercial kitchen grease lines
  • Scale and sludge that a cable only punched through
  • Tree roots that need to be cut and flushed (root removal)
  • Storm and parking-lot lines loaded with sand (storm drain cleaning)
  • French drains clogged with silt (French drain jetting)
  • Narrowed cast iron, sometimes together with descaling

When jetting is not the answer

Jetting cleans pipe. It does not repair it. A collapsed pipe, a badly offset joint, or a section that has rotted through should not be jetted at high pressure. A belly, or sag, will still hold water after cleaning. If the camera shows a structural problem, we will tell you plainly rather than sell a cleaning that cannot fix it.

Hydro jetting near you

We provide hydro jetting for homes and businesses in Fort Lauderdale, Oakland Park, Pompano Beach, Hollywood, Plantation, Davie, Sunrise, Weston, Coral Springs, Boca Raton, Boynton Beach, Delray Beach, West Palm Beach, and the rest of Miami-Dade, Broward, and Palm Beach Counties.

Local jetting pages: hydro jetting in Fort Lauderdale, Hollywood, Pompano Beach, Coral Springs, Plantation, and Davie; sewer jetting in Fort Lauderdale, Hollywood, and Pompano Beach; and restaurant grease line jetting in Fort Lauderdale.

FAQ

Frequently asked questions

What is hydro jetting?

Hydro jetting is a drain-cleaning method that sends high-pressure water through a hose and specialized nozzle to loosen and flush material inside a pipe. Unlike a cable that often bores a path through a blockage, jetting is used to scrub along the pipe wall and carry grease, sludge, scale, and debris out of the line when the pipe is in condition to take that pressure.

What is sewer jetting?

Sewer Jetting is another name for hydro jetting when the work is done in a sewer or main drain line. The tool is the same idea: pressurized water, a nozzle matched to the job, and a line that has been evaluated so the method fits the pipe. People searching for sewer jetting and hydro jetting are usually describing this full-diameter water cleaning.

How is hydro jetting different from snaking or cabling?

A drain snake or cable machine spins a cutting head or auger to break through a clog and restore some flow. That can be the right first step on many household blockages. Hydro jetting uses water to scour the circumference of the pipe so grease, sludge, and film are less likely to be left on the wall. The comparison table on this site walks through those differences in plain language.

Is hydro jetting safe for older pipes?

Not every pipe should be jetted at high pressure. Age, material, offsets, and existing damage all matter. The careful approach is to learn what you can about the line — including a camera inspection when the pipe is accessible and not completely holding water — and then choose pressure, nozzle, and method accordingly. If jetting is not the right tool, we will say so.

Do you inspect with a camera before jetting?

When the line is accessible and the camera can travel, a pre-job look helps confirm what is in the pipe and whether the wall can take pressurized water. After cleaning, a second look is often used so you can see whether the wall is actually clear. Standing water or limited access can delay or change that sequence; we explain those limits on site.

What can hydro jetting remove from a pipe?

When the pipe can take it, jetting is used on grease, soap and sludge film, sanitary debris, sand and sediment, scale, roots, and some hardened deposits. It is not a repair method for a collapsed, badly offset, or broken pipe, and it will not replace a lining or pipe-replacement decision if the camera shows structural failure.

Will jetting fix a broken or collapsed pipe?

No. Jetting cleans. If a camera shows a break, a belly that holds water, a severe offset, or a collapse, cleaning may still help you diagnose the line, but it does not rebuild the pipe. We would rather show you that condition than pretend a cleaning is a structural repair.

Is hydro jetting messy?

The work happens inside the pipe, from a cleanout, roof vent, or other access point when one is available. Water and debris are directed back through the line or recovered as the job requires. We work to protect the area around the access point. Every property is a little different, and we will explain the setup before starting.

How long does hydro jetting take?

A typical residential main line takes a few hours, including setup and camera work. Heavy roots, heavy grease, long runs, or difficult access take longer. We give you a realistic idea once we know the line.

How often should a sewer line be hydro jetted?

There is no single schedule. Many homes only need jetting when a problem develops. Lines with recurring roots or grease, and most restaurant grease lines, do better on a schedule set from what the camera shows.

Can hydro jetting damage pipes?

On a sound pipe, with the right nozzle and pressure, jetting cleans without damaging it. Cracked, thin, or collapsed pipe can be damaged, which is why we camera the line first.

What size pipes can you jet?

We have jetters for lines from 1 inch up to 36 inches and larger pipes. That covers small kitchen and bathroom lines, main sewer lines, commercial grease lines, and large storm drains and culverts. We match the jetter, hose, and nozzle to the size and condition of the pipe.

Need Drain Cleaning Today?

We're Ready to Help!

(954) 914-5151

All calls answered by the owner-operator.

Call (954) 914-5151