Fort Lauderdale · Broward County

Hydro Jetting in Fort Lauderdale, FL

High-pressure water cleaning for drain and sewer lines in Fort Lauderdale homes, condos, restaurants, and commercial buildings. Grease, roots, scale, and sludge removed from the pipe wall. Call (954) 914-5151.

Hydro jetting for Fort Lauderdale drain and sewer lines

Hydro jetting sends water at high pressure through a hose and a nozzle that is fed into the pipe from a cleanout. Jets on the back of the nozzle pull the hose forward and spray the full circle of the pipe wall as it travels, so grease, sludge, scale, and root fibers are cut loose and washed downstream. The result is a line that is clean from wall to wall, not just a hole punched through the middle of a clog.

That matters in Fort Lauderdale because so many of the city's clogs are the coating kind. Restaurant grease, decades of scale inside old cast iron, and fine roots in older laterals all cling to the pipe. A cable can open them up for a while, but the coating stays behind and the line closes again. Sewer-Jetting.com is a family-owned, owner-operated company that does this work every day, and every call to (954) 914-5151 is answered by the owner-operator.

Why Fort Lauderdale lines need jetting

  • Post-war homes with aging cast iron. A large share of the city east of I-95 was built in the 1940s, 1950s, and 1960s. Cast iron from that era rusts from the inside, leaving a rough, narrowed wall that catches paper and grease. A descaling nozzle or a descaling pass can restore the opening when the pipe is still sound.
  • Grease from a busy restaurant scene. Las Olas Boulevard, Himmarshee Village, Flagler Village, and the beach strip run a lot of kitchens close together. Grease cools and hardens on the wall of the line. Jetting is the method that actually removes it.
  • Roots in a city full of mature trees. Ficus, oaks, and palms in older yards send fine roots into lateral joints. A root-cutting nozzle trims the mass, and flushing carries it out. See root removal.
  • Condo and apartment stacks. Towers on the beach and the Intracoastal, and older garden apartments inland, put many kitchens on one stack. Soap film and grease build up faster than in a single-family line.

How we hydro jet a line in Fort Lauderdale

Listen

You describe which drains are slow, how often it happens, and what has been tried before.

Look

When the line can be seen, a camera inspection shows the buildup and whether the pipe can take pressure.

Jet

We pick the nozzle and pressure for that pipe and work the full length from the cleanout.

Confirm

A second camera pass, when possible, shows the clean wall so you know the job is done.

Nozzles matched to the problem

A jetter is only as good as the nozzle on the end of the hose. A penetrating nozzle has a forward jet for breaking into a hard stoppage. A flushing nozzle puts most of its water backward to scour the wall and carry debris out. A root-cutting nozzle trims roots that have grown through joints, and a descaling nozzle works on the rough buildup inside old cast iron. On many Fort Lauderdale jobs we use more than one, in that order, to open the line and then clean it properly.

Jetters for lines from 1 inch to 36 inches and larger

We have jetters for lines from 1 inch up to 36 inches and larger pipes, from trailer-mounted units to combination vac/jetter trucks. That lets us clean a kitchen branch line in a Victoria Park bungalow, a grease line behind a restaurant downtown, and a large main for a condo tower or commercial building. For the bigger mains, storm sewers, and shared community lines, see sewer jetting in Fort Lauderdale.

When hydro jetting is not the right call

Jetting cleans pipe. It does not repair it. If the camera shows a collapsed section, a badly offset joint, or cast iron that has rotted thin, high pressure is not the right tool, and we will say so before any work starts. A sag in the line will still hold water after cleaning. And a single slow bathroom sink usually does not need a jetter at all. A standard drain cleaning in Fort Lauderdale may be all it takes.

Homes, condos, restaurants, and HOAs

We jet lines for single-family homes, duplexes, condo buildings, restaurants, hotels, marinas, offices, and plazas. Associations and property managers can schedule jetting of shared mains and amenity drains, and camera footage helps a board see what was in the line. See our HOA and property manager page. Restaurants can set up recurring grease-line jetting through our maintenance programs, often planned outside service hours when the site allows.

Hydro jetting across Fort Lauderdale

We work across the city, from downtown, Flagler Village, and Victoria Park to Rio Vista, Colee Hammock, Sailboat Bend, the Las Olas Isles, Harbor Beach, Coral Ridge, Imperial Point, and the Galt Ocean Mile, and west to Lauderdale Manors, Riverland, and Melrose Park. For every service we offer in the city, see our Fort Lauderdale service area page. For background on the method, read what is hydro jetting? and hydro jetting vs. snaking, or see our main hydro jetting page.

Call (954) 914-5151 or request a free estimate for hydro jetting in Fort Lauderdale.

FAQ

Frequently asked questions

How much does hydro jetting cost in Fort Lauderdale?

It depends on the line: its size, length, access, and what is in it. We do not publish a price list. Call (954) 914-5151, describe the property and the problem, and we will give you a free estimate.

Is hydro jetting safe for old cast iron in Fort Lauderdale homes?

Often, yes, if the pipe is still structurally sound. Badly corroded, cracked, or thin cast iron should not be jetted at full pressure. That is why we camera the line first when it can be seen and match the nozzle and pressure to what we find. Sometimes descaling is the better first step.

How long does a hydro jetting job take?

It depends on the length of the line, how much buildup is in it, and the access. A residential main is usually a much shorter job than a commercial grease line or a large shared main. We can give you a better idea once we know the property.

Will hydro jetting fix a clog that keeps coming back?

If the cause is buildup on the pipe wall, such as grease, scale, or roots, jetting removes it and the line usually stays open much longer. If the cause is a sag, an offset, or a broken section, a camera will show it, and we will tell you plainly that cleaning alone will not fix it.

Do you hydro jet restaurant grease lines in Fort Lauderdale?

Yes. Commercial grease-line jetting is a regular part of our work, and visits can often be scheduled outside service hours when the site allows.

Need Drain Cleaning Today?

We're Ready to Help!

(954) 914-5151

All calls answered by the owner-operator.

Call (954) 914-5151